' A' Coil with 3/16" top hole. Uses 10-32 retaining nut with a 3/8" wrench size. Has black wire. Old style. Used with 155-0804. Meyer Diamond Snow Plow Parts USES 10-32 RETAINING NUT OLD STYLE, USED W/155-0804
'A' Coil with 3/8" top hole. Uses 3/8-24 retaining nut. Black wire. New Style. Use with 155-0807. BLACK WIRE, NEW STYLE USED W/155-0807
A Seal Kit FOR MEYER
'A' Solenoid Valve & Coil Assembly. New Style. Black Wire.
'A' Solenoid Valve & Coil Assembly. Old Style, has black wire
'A' Valve. 1/2" stem with 3/8-24 top thread. New Style. Use with 155-0806. NEW STYLE USED w/155-0806
'A' Valve. Has 3/8" stem with 10-32" top thread. Old style. Used with 155-0803. OLD STYLE USED W/155-0803
B Coil, Red Wire RED WIRE
B Seal Kit FOR MEYER
B Solenoid Ball & Spring Kit
B Solenoid Valve Assy, Red Wire. RED WIRE
"B" Valve FOR MEYER
C Coil, Green Wire GREEN WIRE
C Seal Kit FOR MEYER
C Solenoid Valve Assembly, Green wire. GREEN WIRE
"C" Valve Cartridge
Brush Kit, 4 piece. Fits our 155-9885 motor. DOUBLE STUD MOTOR
NYLON LOCK NUT 5/16 - 24
"A" coil, square design, plastic, fits 1/2" stem FITS 1/2" STEM USES 155-0807 VALVE
Bolt 3/8"-16 x 3-1/4" Gr.5
Cover & Seal Assembly $INCLUDES LARGE O-RING SEAL & WIPER SEAL & SLEEVE. DOES NOT INCLUDE PRESSURE RELIEF ASSEM ALSO, SUGGEST NYLITE WASHERS
Motor Mounting Plate, E-60, use with single stud motor. O-RING AND SEAL INCLUDED
Crossover Seal Kit - Crossover seal kit Includes seals denoted with " ** " on drawing
Crossover Valve Kit. Used on E-47, E-57 and E-60. Click here for complete instructions on disassembly and reassembly of the valve. Meyer Diamond Snow Plow Parts
Packing Cup, 5/8" ID, 1-3/4" OD. Fits all E-47 and E-57 units. Also fits E-58H, E-60H and some newer E-60's.
Cylinder. Fits E47H, E57H, E58H & E60H
Cylinder Kit. Includes cylinder, piston and follower. Fits E60.
Stud, fits E60. Sold Each SOLD EACH
Cylinder tank (fits E60)
Cylinder tank (fits E60H) FITS E60H
4.5" Motor, twin post. Double Stud Motor. ISKRA MOTOR $MOTOR SPINS CW LOOKING @ TANG
Replaces E-47, E-47H, E-57, E-57H, E-60 & E-60H.
External Adjustment Kit - This kit allows you to adjust the lowering of your E60 plow, lock it, and leave it adjusted correctly without the worry of it changing. Over time (sometimes weekly) the factory adjustment screw will turn by itself making your plow float or drop quickly. Then you have to guess where the factory screw needs to be, adjust it, reassemble and try again (sometimes many times before you get it right) just to have it happen all over again a week later. Our kit replaces the factory screw with an external adjustment (no guess work) then locks into position. Saves aggravation and time. ADJUSTS DROP SPEED OF E60 PUMP
Filter FITS 1/2" AND 9/16" KITS
Ram, Electro Touch, 8" stroke. Fits E47H, E57H, E58H & E60H USED IN E47H, E58H AND E60H 13-3/16" OAL
Ram, Electro Touch, 6" stroke. Fits E46, E47, E57 & E60. Does not fit 'H' models. $EXCEPT E46H, E47H & E60H $11 3/16" OVERALL LENGTH
Rigid Elbow, Short, E-60
Rigid Elbow, Tall, E-60
Master Seal Kit for E-60 and E-60H (Parts included in this kit are denoted with a "#" following the index no)
Motor plate cover w/tabs for 155-9885 double stud motor FITS E60/E60H W/155-9885 MOTOR O-RING AND SEAL NOT INCLUDED
5/16" Nyltite Washer
O-Ring, 1-15/16" I.D., fits E60H
O-Ring, 1-1/2" I.D., fits E60
O-Ring 1/4" I.D.
O-Ring 3-1/2" I.D.
O-Ring 3/8" I.D.
O-Ring 4-3/4" I.D.
O-Ring 5/16" I.D.
O-Ring 7/16 I.D.
O-Ring 9/16 I.D.
Service Manual for Meyers E-60 Lift Pumps
Packing Cup, 1" ID, 1-1/4" OD. Fits E-60
Pilot Check Valve Kit $BALL,SPRING,PLUG
Piston, 1-1/2" dia. Fits E60
Piston, 1-3/4" Diameter. Fits E47, E47H, E57, E57H, E58H and E60H. Does not fit E60
Piston follower, fits all E-47, E-57, E-58 and E-60H units.
Plug w/O-Ring 9/16"
Plug with O-Ring 9/16" hex head
Plug, Valve Block
Pressure Relief Valve w/Bushing
Pump Check Valve - (O-Ring*, Seat, Ball, Spring) O-RING,SEAT,BALL,SPRING
Pump Mounting Plate
Pump Shaft Seal
Ram Assembly complete. Fits E60. Does not fit E60H 6in STROKE, 11-3/16" OAL INCLUDES RAM, PISTON, PACKING CUP, FOLLOWER, NUT FITS E60 ONLY
Sleeve that fits E-60
1-1/8" I.D. O Ring
Stud (fits E60H) sold each FOR E60H, SOLD EACH
TOP CAP KIT INCL:PRESSURE RELIEF, CAP, NUTS AND SEALS
Valve Assembly with coupler, 12V. THAT FITS E-58H